Exactly How to Install a Bathtub
Exactly How to Install a Bathtub
Blog Article
How do you feel in regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a tub isn't specifically brain surgery, yet it does require strong plumbing, carpentry, and often, tiling abilities. Changing an old bath tub with a brand-new one is likewise a reasonably hard task. If the old bathtub is easily easily accessible, the job can move easily; if you need to open up a wall to remove the old tub and also place the brand-new bathtub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will certainly require an assistant to leave the old tub and embeded in the brand-new one. Make certain you have certified yourself for the job as well as are comfortable attempting it. Rather than working with a professional to take over a halfway-completed project, it is much better to consider using one prior to you begin. Opportunities are you might need a professional plumber to make tube links.
This post will aid you set up a new bath tub in your restroom if you have actually already acquired a new bathtub and do not need to alter the arrangement of your previous water system pipes.
Your devices as well as material list must consist of the following:
Planning for the Setup
Firstly, the supporting frame provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to see to it that if the faucet features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps device to avoid pressure on the bathtub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of all of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its last position.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the water supply. After doing so, turn on the taps to drain any type of water continuing to be in the system. The process of getting rid of the existing faucets can be quite troublesome because of the limited accessibility that is frequently the situation.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have been eliminated, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing compound.
Before moving on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Bathtub
Making use of both wooden boards under its feet, place the bath tub in the needed placement. The wooden boards are helpful in equally spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four tiny factors.
The following goal is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the bathtub till the level reviews level.
To mount faucets, fit all-time low of the outermost adaptable faucet port to the suitable supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the water as well as inspect all joints and also brand-new pipework for leakages as well as tighten them if necessary. Load the tub and also examine the overflow electrical outlet as well as the normal electrical outlet for leakages.
Ultimately, take care of the bath paneling as described in the supplier's user's manual. Tiling and sealing around the bath tub ought to wait until the bath tub has been used at the very least once as this will resolve it into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin making certain that the washing machines are in area between the faucet and the sink. Safeguard the tap in position with the manufacturer given backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet connectors. The previous type ought to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath fulfills the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to break an inflexible seal, causing the water to pass through the wall in between the bath and the tiling, causing complications with moisture and also possible leakages to the ceiling below.
You can select from a range of coloured sealants to blend in your components and installations. They are offered in tubes and also cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of soaked paper or soft rope. Keep in mind to constantly fill the bath tub with water before sealing, to permit the movement experienced when the tub remains in usage. The sealant can break rather very early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the marketplace. It is recommended to fit the ceramic tiles using water-resistant or water-proof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you liked our section about A Step-by-Step Guide to Installing a Bathtub. Thanks so much for spending some time to read our post. Liked our blog? Please share it. Let someone else check it out. Thanks for your time. Kindly check up our website back soon.
Book 24/7 Report this page